Water Potential Calculator
Adds up the components of water potential (Ψ = Ψs + Ψp + Ψg, plus hydrostatic, overburden and matric terms for soils) to show which way water will move. Solute potential can be typed in or worked out from the solute concentration with Ψs = −iCRT, using the ionization constant, molarity and temperature in °C or K. You can also solve backwards for the pressure (turgor) potential or for the solute potential and the concentration that would produce it, in bar, MPa, kPa, atm, psi or hPa.
- Ψs = −iCRT treats the solution as dilute; the osmotic coefficient φ can correct for non-ideal behaviour.
- Concentration is entered as molarity (mol/L). The formula is sometimes written with molality (mol/kg); the two are nearly equal for dilute aqueous solutions.
- Every component is in the same pressure unit chosen at the top.
- Results describe equilibrium tendencies; they do not predict the rate of water movement.
Formula
Ψ = Ψs + Ψp + Ψg (+ Ψh + Ψov + Ψm). Solute potential Ψs = −i × φ × C × R × T, with R = 8.314 J/(mol·K) = 0.08314 L·bar/(mol·K), C in mol/L and T in kelvin.
- Water moves from higher (less negative) to lower (more negative) water potential. Pure water at atmospheric pressure is the reference, Ψ = 0.
- Solute potential is never positive: dissolved particles always lower it. i is the ionization constant (1 for sucrose, 2 for NaCl), φ the osmotic coefficient (1 for an ideal solution) and T = °C + 273.15.
- R = 8.314 Pa·m³/(mol·K). With C in mol/L this is 0.08314 L·bar/(mol·K); AP Biology rounds it to 0.0831, which changes results by less than 0.05%.
- Solving for Ψp gives Ψp = Ψ − Ψs − (other components); solving for Ψs gives Ψs = Ψ − Ψp − (other components) and C = −Ψs ÷ (iφRT).
- Overburden potential must be zero or positive and matric potential zero or negative; gravitational and hydrostatic terms may have either sign. Blank optional components count as 0.
- Results are shown to 4 significant figures. Temperatures from −20 °C to 100 °C and magnitudes up to 1,000 MPa are accepted.
0.1 M sucrose in an open beaker at 22 °C
Inputs
- Solve for: total
- Pressure unit (inputs and results): bar
- Solute potential (Ψs) based on: concentration
- Ionization constant (i): 1
- Molar concentration (C): 0.1 mol/L
- Osmotic coefficient (φ): 1
- Temperature (T): 22
- Temperature unit: C
- Pressure potential (Ψp): 0
- Gravitational potential (Ψg): 0
- Hydrostatic (pneumatic) potential (Ψh): 0
- Overburden potential (Ψov): 0
- Matric potential (Ψm): 0
T = 22 + 273.15 = 295.15 K. Ψs = −1 × 1 × 0.1 mol/L × 0.08314 L·bar/(mol·K) × 295.15 K = −2.454 bar. The beaker is open, so Ψp = 0 and Ψ = −2.454 bar (−0.2454 MPa). Pure water placed next to this solution across a membrane would flow into it.
Sources & references
Frequently asked questions
How do I calculate solute potential?
Use Ψs = −iCRT. Multiply the ionization constant i by the molar concentration C (mol/L), the gas constant R (0.0831 L·bar/(mol·K)) and the absolute temperature T (°C + 273.15), then make the result negative. For 0.2 M NaCl at 25 °C: −2 × 0.2 × 0.0831 × 298.15 ≈ −9.9 bar. This calculator uses R = 0.08314, i.e. 8.314 J/(mol·K).
Which way does water move?
From the region of higher water potential to the region of lower (more negative) water potential. Adding solute lowers Ψ; adding pressure raises it. A cell with Ψ = −3 bar placed in a solution of Ψ = −1 bar gains water until the two are equal, usually because its turgor pressure rises.
What is pressure potential and can it be negative?
Pressure potential is the physical pressure on the water. In a turgid plant cell the wall pushes back on the expanding protoplast, giving a positive Ψp of several bar. In an open container Ψp = 0, and in xylem vessels water is pulled up under tension, so Ψp is negative.
What units is water potential measured in?
Water potential is energy per unit volume, which has the same dimensions as pressure, so it is quoted in pascals. Plant physiologists usually use megapascals (MPa), while AP Biology problems use bars. 1 MPa = 10 bar = 1,000 kPa ≈ 9.87 atm.
What is the ionization constant for sucrose, NaCl and CaCl₂?
Sucrose and glucose do not dissociate, so i = 1. NaCl splits into Na⁺ and Cl⁻ (i = 2) and CaCl₂ into Ca²⁺ and two Cl⁻ (i = 3). Real salt solutions behave slightly less than ideally; you can account for this with the osmotic coefficient φ (about 0.93 for 0.1 M NaCl).
What happens to a plant cell in pure water?
The cell's solutes give it a negative Ψs, so water flows in from the pure water (Ψ = 0). As the cell swells the wall resists and Ψp rises until Ψp = −Ψs and the cell's total Ψ reaches 0. Choose “Solve for pressure potential” with Ψ = 0 to find that turgor pressure.
Related calculators
Molarity Calculator Calculates the molarity of a solution, or works backwards to the mass of solute or the volume of solution you need for a target molarity. Molarity is the amount of dissolved substance in moles per litre of solution (mol/L, written M). Enter the molar mass with the mass of solute and the final volume, a target molarity, or a mass concentration in g/L, and get the molarity, moles of solute and concentration. Molar Mass Calculator Calculates the molar mass of a chemical compound. Type a formula such as H2O, Ca(OH)2, Al2(SO4)3 or the hydrate CuSO4·5H2O, or pick elements from the full periodic table (all 118) and set how many atoms of each. The calculator adds up the atomic weights and shows the molar mass in grams per mole, the number of atoms, and each element's mass contribution and percentage by mass. pH Calculator Calculates pH, pOH, the hydrogen ion concentration [H+] and the hydroxide ion concentration [OH-] for aqueous solutions at 25 °C. Start from any one of these four values, or from the concentration of a strong acid, a strong base, or a weak acid or base chosen from a list (or with your own Ka or Kb). The calculator shows whether the solution is acidic, neutral or basic and, for weak acids and bases, how much of it is ionised. Mulch Calculator Calculates how much mulch you need to cover a garden bed. Choose imperial (feet and inches, result in cubic yards) or metric (metres and centimetres, result in cubic metres), describe the bed as a rectangle, a circle or a known area, and enter the depth of the layer. You get the volume of mulch, the number of whole bags, and optionally the cost and weight of the bags or the cost of bulk delivery.