Rebar Calculator

Slab dimensions
ft
ft
Spacings
in
Centre-to-centre distance between neighbouring bars, the same in both directions.
in
Distance from each slab edge to the outermost bar.
At the supplier
ft
The length the bars are sold in, often 20 ft or 6 m.
per ft
Optional. Price per unit length, in any currency.
Construction Updated 31 Oct 2026

Estimates the reinforcing steel for a rectangular concrete slab laid out as a square grid. Enter the slab length and width, the spacing between bars and the cover from the slab edge to the grid, and the length of the bars your supplier sells. You get the grid size, the number of bars running each way, the total length of rebar, the number of stock bars to buy (rounded up) and, if you add a price, the cost.

  • The slab is a rectangle and the grid spacing is the same in both directions.
  • Each grid line is one continuous run; offcuts from stock bars are reused where they fit, so only the total length matters.
  • Lap splices, hooks, chairs and tie wire are not included.
  • Prices are entered by you; no currency conversion is applied.

Formula

Grid length = slab length − 2 × edge; grid width = slab width − 2 × edge. Bars lengthwise = ⌈grid width ÷ spacing + 1⌉; bars widthwise = ⌈grid length ÷ spacing + 1⌉. Total length = bars lengthwise × grid length + bars widthwise × grid width; stock bars = ⌈total length ÷ bar length⌉; cost = stock bars × bar length × price
  • The grid starts one edge distance in from every side of the slab, so each grid dimension is the slab dimension minus twice the edge distance.
  • Across a grid width W with spacing s there are W ÷ s gaps and one more bar than gaps; when W ÷ s is not whole, the count is rounded up so no gap is wider than s.
  • Spacings and edge distances are entered in inches (centimetres) and divided by 12 (100) to give feet (metres) before they are combined with the slab size.
  • Stock bars are rounded up to whole bars. The total cost is the number of whole bars times the price of one bar (bar length × price per unit length).
  • Lap splices, bends, chairs and tie wire are not included; add them to the total length if your design needs them.

6 m × 4 m slab, 40 cm grid, 8 cm from the edges, 6 m bars at 2 per metre

Inputs
  • Units: metric
  • Slab length: 6
  • Slab width: 4
  • Rebar spacing (grid): 40
  • Edge to grid: 8
  • Length of one stock bar: 6
  • Rebar price: 2

Grid = 6 − 2 × 0.08 = 5.84 m by 4 − 2 × 0.08 = 3.84 m. Bars lengthwise = ⌈3.84 ÷ 0.4 + 1⌉ = ⌈10.6⌉ = 11, bars widthwise = ⌈5.84 ÷ 0.4 + 1⌉ = ⌈15.6⌉ = 16. Total = 11 × 5.84 + 16 × 3.84 = 125.68 m, which needs ⌈125.68 ÷ 6⌉ = ⌈20.95⌉ = 21 bars. Each bar costs 6 × 2 = 12, so the rebar costs 21 × 12 = 252.

Sources & references

Frequently asked questions

How do I calculate the cost of rebar for a slab?
Find the total length of bar the grid needs, divide by the length of one stock bar and round up, then multiply the number of bars by the price of one bar. The calculator does all three steps when you enter the price per foot or metre.
How do I calculate the weight of rebar?
Weight = (π × d² ÷ 4) × length × density, where d is the bar diameter. Steel is about 7,850 kg/m³ (490 lb/ft³). For example, 10 m of 12 mm bar weighs about 3.1416 × 0.012² ÷ 4 × 10 × 7,850 ≈ 8.9 kg.
What do rebar sizes like #4 mean?
In US inch-pound sizes, the number is the nominal diameter in eighths of an inch for sizes #3 to #8: #4 is 4/8 = 1/2 inch (12.7 mm), #5 is 5/8 inch (15.9 mm). The matching soft-metric names are No. 13 and No. 16, which give the diameter in millimetres.
Do I need rebar in a patio slab?
Not always. Lightly loaded slabs on well-compacted ground are sometimes built with wire mesh, fibres or no reinforcement, but slabs that carry vehicles or heavy loads need it. Check local practice or ask a structural engineer.
Should I weld rebar together?
Usually not. Ordinary reinforcing steel can become brittle when welded without control, so crossing bars are normally tied with soft steel wire (about 1/16 inch or 1.6 mm). Only weld bars that are specified as weldable, following the engineer's details.

Related calculators

Concrete Slab Calculator Calculates the volume of concrete for rectangular slabs, footings and walls or for round columns and post holes. Choose imperial (feet and inches, result in cubic yards) or metric (metres and centimetres, result in cubic metres), enter the dimensions and how many identical pours you need, and add a waste allowance. If you use pre-mixed bags, enter the concrete density and bag weight to get the total weight, the number of bags and their cost. Area Calculator Finds the area of 2D shapes: rectangle, square, triangle (from base and height, three sides, two sides and the angle between them, or two angles and the side between them), circle, semicircle, circular sector, ellipse, trapezoid, parallelogram (three ways), rhombus (three ways), kite (two ways), regular pentagon, hexagon and octagon, annulus (ring), any quadrilateral from its diagonals and any regular polygon. Pick the shape, enter its dimensions in any length unit (angles in degrees or radians), and you get the area in that unit squared, plus square metres and square feet, and the perimeter where the inputs fix it. Handy for working out the area of a room, a garden bed or a patio before buying flooring, mulch or bricks. Square Footage Calculator Calculates the square footage of a room, floor, lot or any surface from its measurements. Choose a rectangle, an L-shaped room split into two rectangles, a circle or a triangle, and enter the dimensions in feet, inches, yards, metres or centimetres. The area is given in square feet, square metres, square yards and acres, multiplied by the number of identical areas if you have several. Add a price per square foot, square metre or square yard to estimate the cost of flooring, carpet, paint or other materials. Brick Calculator Estimates how many bricks you need for a wall. Work in metric (metres and millimetres) or imperial (feet and inches), enter the wall length and height or its area, deduct doors and windows, and give the brick size, mortar joint and wall thickness (half-brick or one-brick). The calculator returns the net wall area, bricks per unit area, the bricks required, the quantity to order with a waste allowance, the wet volume of mortar and, optionally, the cost of the bricks.