Log Reduction Calculator
Measure how well a disinfectant, sanitizer, heat step or filter kills microbes. Enter the colony forming units (CFU) before and after treatment, each with its own power-of-ten multiplier, to get the log reduction and percent reduction. You can also convert between log and percent reduction, or work out the surviving CFU (or the starting load) needed for a target 3-log, 5-log or 6-log kill.
- The initial count comes from an untreated control that represents the load before treatment.
- Both counts are corrected for dilution and expressed on the same basis (per mL, per carrier, etc.).
- Log reduction uses base-10 logarithms.
Formula
Log reduction = log₁₀(initial CFU ÷ final CFU). Percentage reduction = (initial CFU − final CFU) ÷ initial CFU × 100 = (1 − 10^(−log reduction)) × 100. Final CFU = initial CFU × 10^(−log reduction)
- Each CFU field is the entered number times its power-of-ten multiplier, so 5 with × 10⁷ means 50,000,000 CFU.
- Log reduction is rounded to 4 decimal places. The percentage keeps enough decimals to show the surviving share to three significant figures, so 5 log is shown as 99.999% rather than rounded up to 100%.
- Reverse solving: initial CFU = final CFU × 10^(log reduction); from a percentage, initial CFU = final CFU ÷ (1 − percentage ÷ 100).
- If no colonies grow (final CFU = 0) the reduction is 100% and the log reduction can only be given as a lower bound, log₁₀(initial CFU).
Disinfectant test: 5 × 10⁷ CFU reduced to 2 × 10⁵ CFU
Inputs
- Calculate: counts
- Reduction is given as: log
- Initial CFU (before treatment): 5
- Multiplier: 7
- Final CFU (after treatment): 2
- Multiplier: 5
- Log reduction: 3
- Percentage reduction: 99.9 %
The ratio is 50,000,000 ÷ 200,000 = 250, so the log reduction is log₁₀ 250 ≈ 2.3979. The percentage reduction is (50,000,000 − 200,000) ÷ 50,000,000 = 99.6%: one microbe in 250 survived the treatment.
Sources & references
Frequently asked questions
How do I convert log reduction to percent?
Percent reduction = (1 − 10^(−LR)) × 100. Each whole log adds a 9: 1 log = 90%, 2 log = 99%, 3 log = 99.9%, 4 log = 99.99%, 5 log = 99.999% and 6 log = 99.9999%. Going the other way, LR = −log₁₀(1 − percent ÷ 100).
What log reduction is considered good?
It depends on the purpose and the governing standard. Hand sanitizer and surface tests commonly look for 3 to 5 log, food-contact sanitizers are often expected to reach 5 log (99.999%), and sterilization processes are designed around much larger theoretical reductions such as a 12-log reduction of resistant spores. Always check the specific test method or regulation that applies.
Why use log reduction instead of percent?
Microbial counts span many orders of magnitude, and percentages crowd together near 100%: 99.9% and 99.999% look almost the same but differ by a factor of 100 in survivors. Log reduction turns each tenfold drop into one unit, so treatments are easier to compare.
What if no colonies grow after treatment?
A count of zero means the survivors fell below the detection limit, not that the log reduction is infinite. Report it as 'greater than or equal to' log₁₀(initial CFU ÷ detection limit). The calculator shows this lower bound assuming one CFU could have been detected; adjust for your plating volume and dilution if needed.
Do the initial and final counts need the same units?
Yes. Use CFU per mL, per carrier or per plate consistently for both, after correcting each for its own dilution factor. The multiplier selects let you enter numbers such as 3.2 × 10⁶ without typing all the zeros.
Related calculators
Bacteria Growth Calculator Models exponential bacterial growth with N(t) = N(0) × (1 + r)^t. Solve for the final number of bacteria, the starting number, the elapsed time, or the growth rate and doubling (generation) time from two counts. Give growth either as a per-period growth rate or as a doubling time, choose seconds through years for every time value, and see the number of generations, the fold change, the specific growth rate and a population-over-time table. Cell Dilution Calculator Plan a cell suspension dilution with C1 × V1 = C2 × V2. Enter any three of the stock concentration, the volume of stock to take, the target concentration and the final volume, each with its own unit (µL, mL, cL or L), and the calculator finds the fourth. It also reports the dilution factor, how much medium or buffer to add, the total number of cells, and a serial dilution plan when the stock volume is too small to pipette accurately. Cell Doubling Time Calculator Work out how long a cell culture takes to double from two measurements of the same growth parameter, such as cell number, cells/mL, confluency or optical density, taken a known time apart. The calculator also gives the exponential growth rate, number of doublings and fold change, and can run the model the other way to predict the final value, the starting value or the time needed from a known doubling time or growth rate.