Wastewater Calculator

Units
Food: primary clarifier effluent
MGD
mg/L
mg/L
Also called the "average primary treated BOD"; it is subtracted from the influent BOD.
Microorganisms: aeration tank
MG
Biology Updated 5 Nov 2026

Runs the everyday process-control numbers for an activated sludge plant, from the primary clarifier through the aeration tank to the secondary clarifier. Pick what you need: the F/M ratio on a BOD or COD basis (from flow and concentration or a known loading, with MLVSS from concentration and tank volume or as a mass), hydraulic retention time, mean cell residence time with or without clarifier solids, sludge age, the sludge volume index from a 30-minute settleometer reading, removal efficiency, or clarifier surface overflow rate. US units use the operator 8.34 lb factor; metric units give kilograms directly.

  • Flows are daily averages and concentrations are representative composite results for the same period.
  • US gallons are used for all gallon units, and 8.34 lb per million gallons per mg/L is applied to US flows and volumes as in operator practice.
  • MLSS is taken as uniform through the aeration tank and clarifiers when they are added to the MCRT inventory.
  • This is a process-control and exam-practice aid; plant decisions and permit reporting must follow your plant's procedures and approved methods.

Formula

Loading (lb/day) = flow (MGD) × concentration (mg/L) × 8.34; solids (lb) = volume (MG) × concentration (mg/L) × 8.34 (metric: kg = m³ × mg/L ÷ 1,000). F/M = BOD or COD loading ÷ MLVSS under aeration. HRT = tank volume ÷ flow. MCRT = MLSS in aeration tank (+ clarifiers) ÷ (effluent solids + WAS solids per day). Sludge age = MLSS in aeration tank ÷ primary effluent solids per day. SVI (mL/g) = settled volume (mL/L) × 1,000 ÷ MLSS (mg/L). Removal (%) = (in − out) ÷ in × 100. Surface overflow rate = flow ÷ clarifier surface area.
  • 8.34 is the weight in pounds of 1 mg/L in 1 million US gallons (8.345 rounded), the factor used on US operator formula sheets. It is applied whenever a flow or volume is in US units; metric units use kg = m³ × mg/L ÷ 1,000 exactly, so a mixed US/metric entry can differ by about 0.06%.
  • The F/M ratio's food is the BOD (or COD) leaving the primary clarifier: influent concentration minus what primary treatment removed, times the flow. The microorganisms are the MLVSS in the aeration tank, so F/M is in lb per day per lb (or kg per day per kg), i.e. per day.
  • MCRT counts all the solids in the activated sludge process and divides by the solids that leave it each day in the secondary effluent and the waste sludge. Leave the clarifier volume blank to count only the aeration tank, as on many state formula sheets.
  • Sludge age uses only the aeration tank and divides by the suspended solids arriving from the primary clarifier each day, so it is a loading-based age rather than a wasting-based one like MCRT.
  • SVI is the volume in millilitres that 1 g of mixed liquor solids occupies after 30 minutes of settling. With a 1 L cylinder the settled reading in mL is already mL/L; other cylinder sizes are scaled to 1 L.
  • Surface overflow rate uses the full water surface (π × diameter² ÷ 4 for a circular clarifier); formula sheets that use 0.785 × D² give the same answer to three figures.

F/M ratio of a 3 MGD activated sludge plant

Inputs
  • What do you want to calculate?: fm
  • Concentration unit: mgL
  • Flow unit: mgd
  • Tank volume unit: MG
  • Organic load measured as: bod
  • What do you know about the food supply?: split
  • Primary effluent flow to aeration: 3 MGD
  • Average untreated influent BOD: 220 mg/L
  • BOD removed by primary treatment: 70 mg/L
  • BOD entering the aeration tank: 150 mg/L
  • Average untreated influent COD: 450 mg/L
  • COD removed by primary treatment: 140 mg/L
  • COD entering the aeration tank: 310 mg/L
  • Loading unit: lb
  • BOD loading to aeration: 3753 lb/day
  • COD loading to aeration: 7756 lb/day
  • Is the aeration tank volume known?: conc
  • Aeration tank volume: 0.75 MG
  • MLVSS concentration: 2000 mg/L
  • Mass unit: lb
  • MLVSS under aeration: 12510 lb
  • Aeration tank volume: 0.75 MG
  • Flow through the tank (primary effluent): 3 MGD
  • MLSS concentration: 2500 mg/L
  • Primary effluent suspended solids: 80 mg/L
  • Secondary clarifier volume (optional): 0.25 MG
  • Secondary effluent flow: 2.9 MGD
  • Secondary effluent TSS: 12 mg/L
  • Waste activated sludge (WAS) flow: 0.06 MGD
  • WAS suspended solids: 8000 mg/L
  • Settled sludge after 30 minutes: 300 mL
  • Sample volume in the cylinder: 1000 mL
  • Influent concentration: 220 mg/L
  • Effluent concentration: 15 mg/L
  • Flow (optional): MGD
  • Flow to the clarifiers: 3 MGD
  • Clarifier shape: circle
  • Length unit: ft
  • Diameter: 80 ft
  • Length: 100 ft
  • Width: 25 ft
  • Number of clarifiers in service: 1

Raw sewage at 220 mg/L BOD loses 70 mg/L in the primary clarifier, so 150 mg/L enters aeration. At 3 MGD the BOD loading is 3 × 150 × 8.34 = 3,753 lb/day. The 0.75 MG aeration tank holds 2,000 mg/L MLVSS, or 0.75 × 2,000 × 8.34 = 12,510 lb. F/M = 3,753 ÷ 12,510 = 0.300 lb BOD per day per lb MLVSS.

Sources & references

  • Formula Sheet for all Wastewater Operator Exams (revised 3/17)
    Indiana Department of Environmental Management · Retrieved 5 Nov 2026

    State operator certification formulas used to verify this calculator: F011 removal efficiency; F012/F035 solids lb = MG × mg/L × 8.34; F017 BOD loading = MGD × mg/L × 8.34; F061/F098 surface loading gpd/sf = flow ÷ area (0.785 × D²); F063/F105 sludge age = aerator TSS lb ÷ primary effluent TSS lb/day; F064 F/M = lb BOD/day ÷ lb MLVSS; F066 MCRT = aeration MLSS lb ÷ (TSS wasted + TSS in effluent, lb/day); F008/F037 detention time = volume ÷ flow.

  • Sludge volume index
    Wikipedia · Retrieved 5 Nov 2026

    Supporting definition (Mohlman, 1934; Jenkins, Richards and Daigger, Manual on the Causes and Control of Activated Sludge Bulking and Foaming): SVI (mL/g) = settled sludge volume after 30 min (mL/L) ÷ MLSS (mg/L) × 1,000.

Frequently asked questions

How do I calculate the F/M ratio?
Divide the pounds of BOD entering the aeration tank each day by the pounds of MLVSS under aeration. A plant sending 3 MGD at 150 mg/L BOD to a 0.75 MG tank at 2,000 mg/L MLVSS has F/M = (3 × 150 × 8.34) ÷ (0.75 × 2,000 × 8.34) = 3,753 ÷ 12,510 = 0.30 per day. The 8.34 cancels when both are in US units.
What is the difference between MCRT and sludge age?
Both divide a solids inventory by a daily solids flow. MCRT divides the solids in the whole activated sludge process (often aeration tank plus clarifiers) by the solids leaving in the effluent and waste sludge. Sludge age divides the solids in the aeration tank only by the suspended solids arriving from the primary clarifier. For example, 15,638 lb of MLSS fed 2,002 lb/day of primary effluent solids has a sludge age of 7.8 days.
How do I calculate SVI?
Let 1 L of mixed liquor settle for 30 minutes, read the sludge blanket in mL, and divide by the MLSS in g/L. 300 mL of settled sludge at 2,500 mg/L (2.5 g/L) MLSS gives SVI = 300 ÷ 2.5 = 120 mL/g, inside the 100–200 mL/g range most plants aim for.
How is hydraulic retention time calculated?
Divide the tank volume by the flow through it, using the same volume unit for both. A 0.75 MG aeration tank receiving 3 MGD has HRT = 0.75 ÷ 3 = 0.25 day = 6 hours. Return sludge flow is not included in this nominal HRT.
What is a typical surface overflow rate?
It depends on the clarifier and the design standard you follow, so check your state or national design criteria. As a calculation example, 3 MGD over one 80 ft clarifier (5,027 ft²) is 3,000,000 ÷ 5,027 = 597 gpd/ft², or about 24.3 m³/m²·day.

Related calculators